Here are some of the frequent questions we get from our customers, if you don’t see your question, please email us at service@b-quiet.com
Simply use PayPal as your check out option. PayPal allows you to pay with your credit card and without needing an account. Simply choose the currency you would like to pay in.

Product

Automotive

Motorhome

Elevators

Home Theatre, Studio or Music

Marine

Ultimate

 •

 

Extreme

V-Comp

H-Liner

 

 

Below is a guide to do your entire vehicle, firewall, floors, doors, trunk and roof based on vehicle size.

Vehicle size:

Total cars sqft:

Recommended number of rolls

Midsize

100-110 sqft

2 x 50ft roll + 1x 12 ft roll

Full size

110-115 sqft

2 x 50ft roll + 1x 12 ft roll

Compact SUV

115-120 sqft

2 x 50ft roll + 2x 12 ft roll

Mid-sized SUV

125-130 sqft

2 x 50ft roll + 3x 12 ft roll

Full size SUV

140-150 sqft

3 x 50ft roll

Pickup

75-85 sqft

1x 50ft roll + 3 x 12 ft roll

Tank

200-300 sqft

6 x 50ft roll

Disclaimer: Calculations are based on average vehicle size. Variations on make and model may occur. Check your owner’s manual for exact specifications.

We suggest B-Quiet Extreme, asphalt based, or Ultimate butyl rubber based throughout the vehicle to control structural borne noises, such as rattles, resonances, vibrations and to slow the propagation of road, engine and exhaust noise into the cabin.

Vcomp is a noise barrier composite consisting of a dense 1/8" vinyl-based polymer barrier with a 1/4" thick foam decoupler. It has a total thickness of 3/8", weighs approximately 1 lb/sq. ft. It is to be installed with the foam towards the source of the noise, with the vinyl barrier blocking those noises from traveling.

For even better reduction of road, engine and exhaust noise, we strongly encourage a layer of Vcomp in addition to the application of Extreme or Ultimate on the floor and lower interior firewall to absorb airborne noises.

People often ask how the products work. We recommend keeping the explanations down to the basics and going from there. A simple explanation of how the Ultimate and Extreme effectively reduce vibrational/road noise by transferring the vibrations and noise to heat, and the V-Comp and H-Liner contain foam to absorb air born sound.

When using this type of sound deadening product in boats, there are a couple of things to consider.

1. B-Quiet Ultimate is the best sound deadening product available when it comes to vibration reduction, resonances and noise traveling through the hull and frame of the boat. It also has the highest heat rating which means it can go closer to the engine.

2. B-Quiet Vcomp is the best product when it comes to deadening sound like water and engine noise. But the Vcomp has a lower heat rating and cannot be used as close to the engine. The Vcomp is also partly open cell foam which means if it gets wet it will hold moisture and is not made for that kind of wear. The best spray adhesive for use with the Vcomp is the 3M Spray 90 which will give you a strong hold.

3. Hliner is good for absorbing and greatly reducing engine noise but does not have a rubberized polymer barrier. It can hold moisture which can create problems as well as wear out the material. All three products should be kept dry and will provide you with excellent sound deadening in a variety of applications.

The best combination of products to use on the doghouse in a motor home is a layer of the B-Quiet Ultimate with a layer of the Hliner over top. This helps reduce vibrations and absorb noise. You may wish to use just one or the other, which is still fine, but for superior sound insulating features as using a combination.

Both products should not get wet on a consistent basis, because the adhesive backing may begin to peel and the Hliner is an open cell foam that will absorb the water. So, we would suggest to only use these products on the inside of your vehicle.

We would suggest that using our Vcomp in your walls may help trap and absorb the noise and keep it from traveling outside the walls of the theater room.

Vcomp is a noise barrier composite consisting of a dense 1/8" vinyl-based polymer barrier with a 1/4" thick foam decoupler. It has a total thickness of 3/8", weighs approximately 1 lb/sq. ft. It is to be installed with the foam towards the source of the noise, with the vinyl barrier blocking those noises from traveling.

Our B-Quiet Ultimate and Dynamat are extremely similar. The largest difference between the two products are cost and the size. We offer our product through direct sales channels saving you money and we can keep our costs far more affordable for the buyer.
[time] minutes ago, from [location]
The cookie settings on this website are set to 'allow all cookies' to give you the very best experience. Please click Accept Cookies to continue to use the site.
You have successfully subscribed!